Two cases can look identical on the shelf and protect completely differently, because the foam inside them isn’t the same material.
The best foam for your case is usually one of two families, polyethylene or polyurethane, and they behave differently under impact, in water, and over years of use. If you’ve ever opened an old case and found the foam crumbling into dust, you’ve already met the difference.
Here’s what each foam is, where you’ll find it, and which one your gear needs.
What Is Polyurethane Foam?
Most pick-and-pluck cubed foam, the kind that ships inside many off-the-shelf cases, is polyurethane. It’s typically an open-cell foam, soft and light, with a structure closer to a sponge than a solid block.
That softness is its strength for the right gear. Polyurethane cushions light, delicate items well, it’s easy to pluck into shape by hand with no tools, and it conforms around irregular objects instead of pushing back on them. For a light kit that gets carried rather than shipped, it gets the job done.
Its weaknesses are time and water. Open cells absorb moisture, and a case stored damp will hold that damp against your gear. Polyurethane, especially the common ester type, also breaks down as it ages: heat, humidity and years cause it to lose resilience, compress flat where gear rests on it, and eventually crumble and shed particles.
It also performs best against a single hard impact: it cushions mainly by crushing, and after a significant hit it doesn’t spring back to its original thickness the way its firmer counterpart does.
Find it in cubed pick-and-pluck foam sets, convoluted lid foam, and soft foam linings in budget and light-duty cases.
What Is Polyethylene Foam?
Polyethylene foam is a closed-cell foam. Instead of a sponge, picture a solid block of sealed cells, which is why it cuts cleanly, holds an edge, and resists water absorption. Most of our custom CNC inserts are cut from firm polyethylene for exactly these reasons.
Under impact, polyethylene behaves differently: it absorbs energy and largely returns to shape, so it keeps protecting through repeated drops instead of packing down after the first few.
That repeatability is why it’s the standard for heavy gear, shipped equipment, and kits that travel daily. It’s also chemically resistant, doesn’t support moisture retention against your gear, and holds up for years without crumbling or shedding.
The trade-offs are felt and process. Polyethylene is firm, and it doesn’t belong in direct soft contact with very delicate finishes without thought to the design. It also isn’t a pluck-it-yourself material: it’s milled, routed or waterjet cut, which is why you meet it in designed inserts rather than in a grid of cubes.
Find it in custom CNC foam inserts, fabricated case interiors for industrial, medical and military equipment, and heavy-duty loadouts.
Comparing Polyethylene vs Polyurethane Foam
|
Polyethylene foam |
Polyurethane foam |
|
|
Cell structure |
Closed cell |
Typically open cell |
|
Water behaviour |
Resists water absorption |
Absorbs and holds moisture |
|
Repeated impacts |
Springs back, keeps protecting |
Compresses and packs down over time |
|
Aging |
Stable for years, no crumbling |
Breaks down with age, heat and humidity, can crumble |
|
Working it |
Milled or cut, designed inserts |
Plucked by hand, cubed sets |
|
Best at |
Heavy, fragile, shipped or daily travel gear |
Light, delicate gear, gentle handling |
Which Foam Is Best For Your Gear?
Choose polyethylene when:
-
the gear is heavy, valuable or fragile
-
the case gets shipped or travels daily
-
it may meet water
-
the insert is expected to last the life of the case
That’s why custom CNC inserts are polyethylene: a fleet case opened in ten years should protect like it did in year one.
Choose polyurethane when
-
the kit is light
-
the handling is gentle
-
the fit needs to happen today with no design step
This is exactly the job cubed foam exists for. Just plan on it being a consumable: inspect it every year or so, and replace a set that has gone flat, dusty or crumbly before it stops protecting and starts shedding onto your equipment.
The two also combine well. A designed insert can pair polyethylene structure with softer contact layers where a finish needs it, which is one more reason a custom insert outperforms a single-material block.
Not sure what is inside your current case, or what a new kit needs? Send us the gear list here and we’ll match the foam type and firmness to the weight of your gear and how fragile it is, or let us design and build a new custom insert for you.
Frequently Asked Questions
Is pick and pluck foam polyethylene or polyurethane?
Usually polyurethane. Cubed foam is designed to be torn by hand, which suits polyurethane's soft open-cell structure. Polyethylene is too firm to pluck, so it’s cut or milled instead.
Why did the foam in my old case crumble?
That’s polyurethane aging. Heat, humidity and time break the material down until it loses its structure and turns dusty or sticky. Cases stored in hot or damp spaces age fastest. Replacing the foam set restores the case, and a polyethylene insert removes the problem for good.
Can polyethylene foam scratch delicate gear?
It’s firm, so pocket design matters: correct sizing, smooth pocket walls and, where a finish is very delicate, softer contact layers built into the insert. A well-designed polyethylene insert protects delicate instruments daily in medical and broadcast work.
Does polyethylene foam float or get waterlogged in a wet case?
It floats. The closed, sealed cells trap air and keep the foam's density below that of water, which is also why it won’t get waterlogged: it doesn’t absorb water, and it won’t hold moisture against your gear the way an open-cell foam can.
